UV光油 - 蒸發電鍍材料 - 塑膠UV清漆
UV light oil - evaporation plating material - plastic UV varnish
UV清漆 - 指甲油UV光油 - 美甲光油
UV varnish - Nail polish UV varnish - Nail Polish
【主要組成】
采用齊聚物、活性稀釋劑、光引化劑為主要原料配制而成
【產品說明】
該產品噴涂或滾涂在基材表面之后，經過UV燈的照射，使其由液態轉化為固態，進而達到表面硬化，其耐刮耐劃的作用，且表面看起來光亮，美觀、質感圓潤。
【使用范圍】
TPU軟膠、PVC軟膠、PEVA軟膠、ABS美甲貼、PP料美甲貼、亞克力等產品噴涂
UV varnish
[main components]
It is made of oligomer, active diluent and photoinitiator
[product description]
After the product is sprayed or rolled on the surface of the substrate, it is irradiated by UV lamp to make it from liquid to solid, so as to achieve surface hardening. It is scratch resistant and scratch resistant, and the surface looks bright, beautiful and smooth.
[application scope]
TPU soft glue, PVC soft glue, PEVA soft glue, ABS nail stick, PP nail stick, acrylic and other products spraying
【理化參數】
[physical and chemical parameters]
【施工工藝】
1.在噴涂前充分清洗底材,以確保優異的附著力和表面效果。
2.本品作業條件,溫度: 15-30℃; 濕度:(RH)≤75%
3.噴涂方式：直接噴涂，噴涂粘度(巖田2號,25℃) : 8 s ~9s
4.干燥條件: 300-400能量
5.噴涂空氣壓力: 4.5-6.5kg/c㎡
6.噴涂距離：10-20cm
7.噴槍口徑：1.1-1.5mm
[construction technology]
1. Fully clean the substrate before spraying to ensure excellent adhesion and surface effect.
2. Operating conditions: 15-30 ℃; Humidity: (RH) ≤ 75%
3. Spraying method: direct spraying, spraying viscosity (Yantian 2, 25 ℃): 8 s ~ 9 s
4. Drying condition: 300-400 energy
5. Spraying air pressure: 4.5-6.5kg/cm2
6. Spraying distance: 10-20cm
7. Diameter of spray gun: 1.1-1.5mm
【施工注意事項】
1：被涂物表面雜物、油污必須清除。
2：施工調薄時請用專用稀釋劑，以免影響漆膜外觀、性能
3：油漆調制后，在使用前一定要靜置10-15分鐘后方可使用
4：涂裝成品在常溫下靜置20-30分鐘后，烘烤70oC*1H效果佳
5：開蓋使用后務必蓋緊,以免吸濕和風干;已加硬化劑之混合漆，不可入原桶，以免硬化
6：嚴格控制溶劑含水氣，禁止用含醇類溶劑
7：遇反常氣候涂裝時,請洽敝司技術員,以尋求適當?shù)耐垦b方法
8：油漆開稀后用300目過濾網過濾
[construction precautions]
1: Debris and oil on the surface of the coating must be removed.
2: Please use special diluent when thinning, so as not to affect the appearance and performance of paint film
3: After the paint is prepared, it must be allowed to stand for 10-15 minutes before use
4: After standing at room temperature for 20-30 minutes, the effect of baking at 70oC * 1H is good
5: Be sure to cover tightly after use to avoid moisture absorption and air drying; The mixed paint with hardener should not be put into the original barrel to avoid hardening
6: Strictly control the water containing gas in the solvent and prohibit the use of alcohol containing solvents
7: In case of abnormal weather coating, please contact our technician to find the appropriate coating method
8: The paint is thinned and filtered with 300 mesh filter
【包裝規格】
色漆20KG，鐵桶4L、25L花藍桶
[package specification]
Paint20kg，Iron bucket 4L, 25L flower blue bucket
【用途范圍及屬性】
主要用于假指甲產品，可以上金蔥粉然后噴UV光油，產品柔韌性好！耐彎曲性好！
[application scope and properties]
Mainly used for false nail products, can be golden onion powder and then spray UV varnish, product flexibility is good! Good bending resistance!
致誠科技根據產品特性匹配最佳的鍍膜工藝方案，
致誠鍍膜優勢特點所在：專業、誠信、極致可靠。
Zhicheng Technology matches the best coating process scheme according to the product characteristics,
Zhicheng coating advantages: professional, honest, extremely reliable.
納米噴鍍 納米噴鍍材料 納米噴鍍設備 納米噴鍍加工 納米噴鍍廠家 納米噴鍍原料 納米噴鍍加工廠家 納米噴鍍配方 納米噴鍍技術 納米噴鍍工藝
納米噴涂 納米噴涂材料 納米噴涂設備 納米噴涂加工 納米噴涂廠家 納米噴涂原料 納米噴涂加工廠家 納米噴涂配方 納米噴涂技術 納米噴涂工藝
銀鏡噴鍍 銀鏡噴鍍材料 銀鏡噴鍍設備 銀鏡噴鍍加工 銀鏡噴鍍廠家 銀鏡噴鍍原料 銀鏡噴鍍加工廠家 銀鏡噴鍍配方 銀鏡噴鍍技術 銀鏡噴鍍工藝
銀鏡噴涂 銀鏡噴涂材料 銀鏡噴涂設備 銀鏡噴涂加工 銀鏡噴涂廠家 銀鏡噴涂原料 銀鏡噴涂加工廠家 銀鏡噴涂配方 銀鏡噴涂技術 銀鏡噴涂工藝
納米電鍍 納米電鍍材料 納米電鍍設備 納米電鍍加工 納米電鍍廠家 納米電鍍原料 納米電鍍加工廠家 納米電鍍配方 納米電鍍技術 納米電鍍工藝
環保電鍍 環保電鍍材料 環保電鍍設備 環保電鍍加工 環保電鍍廠家 環保電鍍原料 環保電鍍加工廠家 小型電鍍設備 環保電鍍技術 環保電鍍工藝
